Force Four
He goes the extra mile
To give you the best.
The FORCE FOUR model meets professional needs that require large charging capacities in hot, poorly ventilated environments or tropical countries. It is equipped with an intuitive control panel and electric motor. The pumping unit, a choice of 3 most powerful, is exposed to ensure a better cooling cycle. It is equipped with the Hyperfilter purification system mounted on a stand-alone system, with automatic condensate drainage. For longer filter life, the Tornado high pressure dryer is recommended. Available as options: the Presec system for filter saturation control, Megafilter oversized filter cartridges, and 2- or 4-outlet remote refill panel.
4-stage high pressure pumping unit.
- Monobloc in aluminum,
- Crankshaft in forged steel
- Forced lubrication on the 4th stage cylinder by gear pump
- Oil filtration
- Aluminum connecting rods
- Main roller bearings
- Roller connecting rod bearings
- 1st, 2nd and 3rd stage cylinders in special cast iron
- 4th stage cylinder in special treated steel.
- Low oil pressure switch.
- Stainless steel intake and exhaust valves
- Interstage cooling pipes in stainless steel
- Separator after the 2nd, 3rd and 4th stage
- Safety valves after each stage
- Oil level sensor
- Prepared for Hyperfilter filter system
Electric motor
One of the fundamental parts of the compressor: the motor transfers the motion to the pumping unit through the belt. Single-phase 7.5 kW or three-phase 7.5 to 11 kW electric motor is available on this model.
Purification at the highest level.
Placed after the last compressor separator and before the pressure holding valve, the Hyperfilter purification system enables reliable treatment of the breathing air according to DIN EN 12021¹ when using original filter cartridges. The separator present between the 2nd and 3rd stage of the purification circuit allows to extract the greatest possible humidity. The filtering capacity with inlet air at 20 ° C and 200 bar is 4300 m³.
Compressor control and automatic condensate drainage system
- Motor protection switch.
- Fixed calibration pressure switch 232 or 300 bar.
- Autostart with pressure differential 15 bar. (optional)
- Transformer.
- Drainage of all separators between individual stages and also of the final separator during compressor operation (standard drainage interval every 15 minutes for a period of 6 seconds).
- Timer for automatic condensate drain.
- Interstage pressure gauges display the working pressure for the individual compression stages. This pressure information allows you to check the tightness of the valves (inlet and outlet) of each stage and to quickly identify potential sources of failure.
Interstage pressure gauges are mounted in the compressor frame.
Standard equipment
4 Filling connections of your choice of DIN 232, DIN 300 or INT/YOKE 232 bar
4 filling hoses of 1.2 m in length
Pressure maintenance valve
Interstage control gauges
Double PED certified Hyperfilter filter system
Purification system on “stand-alone” structure
Automatic condensate drain
Oil level control with automatic shutdown
Oil pump
Frame color Black RAL 9005
Technical data
Type of gas
Breathing air (EN 12021) – Nitrox 40% max O2 – Helium – Nitrogen
Intake pressure
Atmospheric max 300 millibars
Nominal pressure
250 bar / 330 bar / 360 bar
Working pressure
250 bar / 330 bar / 360 bar
Max working pressure
420 bar
Permissible ambient temperature range
-10° C ÷ +40° C
Permissible altitude
0 ÷ 1.500 m SLM
Max permissible tilt
15°
Design
Cabinet aperto
Operating voltage, standard
230 V, 60 Hz (elettrico monofase) 400 V, 50 Hz (elettrico trifase)
Other operating voltage
On three-phase electric motor at 60Hz the power (kW / Hp) increases by 20%.230 V, 50 Hz / 440 V, 60 Hz / 400 V, 60 Hz
Oil
Synthetic Coltri Oil ST 755
Oil change interval
Every year / 1,000 h
Frame
Steel thickness 1.5 mm – Color RAL Black 9005 – Powder coating – scratch-resistant
Compressor
Charging rate
Measured during 10 liters cylinder filling from 0-200 bar tolerance +/- 5% at + 20° C ambient temperature.400 EM
400 l/min
24 m3/h
14.1 CFM
450 ET
450 l/min
27 m3/h
15.9 CFM
650 ET
650 l/min
39 m3/h
23 CFM
Purification system
2 Hyperfilter su struttura stand-alone
Cooling air flow, min.
400 EM
4.050 m3/h
450 ET
4.050 m3/h
650 ET
4.820 m3/h
Weight
Standard model. Weight and dimensions may vary depending on accessories.400 EM
250 kg
551 lb
450 ET
250 kg
551 lb
650 ET
260 kg
573 lb
Dimensions
(W x D x H)115 x 60 x 79,6 cm
45.3 x 23.6 x 31.3 in
Motor
Power
400 EM
7.5 kW
10 Hp
450 ET
7.5 kW
10 Hp
650 ET
11 kW
15 Hp
Type
400 EM
Single-phase electric
450 ET
Three-phase electric
650 ET
Three-phase electric
Operating voltage/frequency
Different voltage / frequency available on request.400 EM
230 V, 60 Hz
450 ET
400 V, 50 Hz
650 ET
400 V, 50 Hz
Rated current
400 EM
41.3 A
450 ET
15 A
650 ET
23 A
Speed (RPM)
400 EM
3.525
450 ET
2.870
650 ET
2.910
Protection class
IP55 (TEFC)
Optional
Available models of Force Four
(Non-standard models available upon request)
Force Four 400 EM
Flow rate: 400 l/min
Cylinder refill (10 liters): 5 minutes
Force Four 450 ET
Flow rate: 450 l / min
Tank refill (10 liters): 4 minutes 30 seconds
Force Four 650 ET
Flow rate: 650 l / min
Tank refill (10 liters): 3 minutes
