Ergo TPS
Less, more.
The best answer to those who want small-sized breathing air compressors, while maintaining high performance. Equipped with four different TPS (Tropical Plus Superdry) pumping units, Ergo TPS is powered by an electric motor. It has a panel with a monitoring system complete with pressure gauges, autostop with adjustable electronic pressure switch, automatic condensate drain and control of the direction of rotation. It is also equipped with two connections for high pressure hoses and an increased filtering system with two Hyperfilters. Optionally, you can add the remote charging panel.
Pumping group
- Monobloc in aluminum,
- Crankshaft in forged steel
- Forced lubrication on 2nd and 3rd stage cylinders by gear pump
- Oversized interstage cooling pipes
- Forged aluminum connecting rods
- Main roller bearings
- Roller connecting rod bearings
- 1st and 2nd stage cylinders in aluminum with hard nicasil coating
- 2nd and 3rd stage slide guide cylinders in aluminum with hard nicasil coating
- 3rd stage cylinder in special treated steel.
- Stainless steel intake and exhaust valves
- Interstage cooling pipes in stainless steel
- Separator after the 2nd and 3rd stage
- Safety valves after each stage
- Prepared for Hyperfilter filter system
- Oil filtration
- Double final separator
Purification at the highest level.
Placed after the last compressor separator and before the pressure holding valve, the Hyperfilter purification system enables reliable treatment of the breathing air according to DIN EN 12021¹ when using original filter cartridges. The separator present between the 2nd and 3rd stage of the purification circuit allows to extract the greatest possible humidity. The filtering capacity with inlet air at 20 ° C and 200 bar is 4300 m³.
Electrical cabinet
- ON / OFF switch with motor protection switch.
- Digital electronic pressure switch that stops the compressor at the final pressure.
- Drainage of all separators between the individual stages and also of the final separator during compressor operation
- Timer for automatic condensate drain.
- Integrated no-load start (automatic drain every time the unit is switched off).
- 5 liter condensate collection tank, with silencer; capacity of about 3 liters, for the ecological disposal of condensate.
- Interstage pressure gauges display the working pressure for the individual compression stages. This pressure information allows you to check the tightness of the valves (inlet and outlet) of each stage and to quickly identify potential sources of failure.
Chassis
Open frame designed to facilitate maintenance operations and portability. The tilting motor-holder plate ensures constant V-belt tension. The protective casing in thermo-formed material conveys the cooling air on the cylinders and on the inter-stage pipes, guaranteeing a high compression efficiency. The control console equipped with inter-stage pressure gauges, the internal temperature indicator, the alarm presence and incorrect phase sequence, the oil lack alarm and the start stop and manual condensate drain commands allow easy management and maintenance of the compressor .
Standard equipment
2 Cylinder connections to choose from DIN 232, DIN 300 or INT / YOKE 232 bar
2 whips 1.2m long
Pressure maintenance valve
Interstage control gauges
Double PED certified Hyperfilter filter system
Cabin internal temperature with automatic switch-off
Automatic condensate drain
Automatic direction of rotation control
Electronic pressure switch with automatic shutdown
Oil level control with automatic shutdown
Oil pump with filter and pressure gauge
Automatic condensate drain with conveyor system in the tank
Carrying handles
Frame color Blue RAL 5002 + Carrying handles
Technical data
Type of gas
Breathing air (EN 12021) – Nitrox 40% max O2 – Helium – Nitrogen
Intake pressure
Atmospheric max 300 millibars
Nominal pressure
250 bar / 330 bar / 360 bar
Working pressure
232 bar / 300 bar / 330 bar
Max working pressure
232 bar (elettrico monofase) – 420 bar (elettrico trifase)
Permissible ambient temperature range
-10° C ÷ +40° C
Permissible altitude
0 ÷ 1.500 m SLM
Max permissible tilt
15°
Design
Open
Operating voltage, standard
400 V; 50 Hz
Other operating voltage
On three-phase electric motor at 60Hz the power (kW / Hp) increases by 20%.230 V, 50 Hz / 440 V, 60 Hz / 230 V, 60 Hz
Oil
Synthetic Coltri Oil ST 755
Oil change interval
1 year / 1,000 h
Frame
Steel thickness 1.5 mm – color Blue RAL 5002 – Powder coating – scratch-resistant
Compressor
Charging rate
Measured during 10 liters cylinder filling from 0-200 bar tolerance +/- 5% at + 20° C ambient temperature.270 EM
270 l/min
16.2 m3/h
9.5 CFM
235 ET
235 l/min
14.1 m3/h
8.2 CFM
315 ET
315 l/min
18.9 m3/h
11.1 CFM
345 ET
345 l/min
20.7 m3/h
12.1 CFM
380 ET
380 l/min
22.8 m3/h
13.4 CFM
Purification system
2 Hyperfilter
Cooling air flow, min.
270 EM
2.400 m3/h
235 ET
1.960 m3/h
315 ET
2.400 m3/h
345 ET
1.960 m3/h
380 ET
2.180 m3/h
Weight
Standard model. Weight and dimensions may vary depending on accessories.270 EM
184 kg
406 lb
235 ET
174 kg
384 lb
315 ET
184 kg
406 lb
345 ET
184 kg
406 lb
380 ET
184 kg
406 lb
Dimensions
(W x D x H)112 x 63 x 77 cm
44.1 x 24.8 x 30.3 in
Motor
Power
270 EM
5,5 kW
7.5 Hp
235 ET
4 kW
5.5 Hp
315 ET
5,5 kW
7.5 Hp
345 ET
7,5 kW
10 Hp
380 ET
7,5 kW
10 Hp
Type
270 EM
Single-phase electric
235 ET
Three-phase electric
315 ET
Three-phase electric
345 ET
Three-phase electric
380 ET
Three-phase electric
Operating voltage/frequency
Different voltage / frequency available on request.270 EM
230 V, 50 Hz
235 ET
400 V, 50 Hz
315 ET
400 V, 50 Hz
345 ET
400 V, 50 Hz
380 ET
400 V, 50 Hz
Rated current
270 EM
13.2 A
235 ET
13.2 A
315 ET
13.2 A
345 ET
13.2 A
380 ET
13.2 A
Speed (RPM)
270 EM
2.840
235 ET
2.850
315 ET
2.840
345 ET
2.850
380 ET
2.850
Protection class
IP55 (TEFC)
Optional
The available models of Ergo TPS
(Non-standard models available upon request)